氣液結合增壓特點特點：
速度快：動作速度較液壓傳動快，且較氣壓傳動穩定；
易使用：缸體裝置簡單，出力調整容易，使用保養方便；
出力大：在相同途徑條件下可達油壓機之高出力，非純氣壓系統可達到；
價格低：設備單價較油壓系統低廉；
易維護：因結構簡單，故維護較油壓系統簡便；
能耗低：持續加壓或停止動作時，不必像純液壓系統那樣，馬達需持續運轉，故可節省能源，且動力來源方便易取，實際能耗相當于油壓系統10%-30%；
無泄漏：能量轉換方便，可以做到零泄漏不必擔心環境污染；
不損模：為適應工藝需要，沖壓力和工作行程在規定范圍內可達到無極可調；
安裝易：多種安裝方式，根據不同工作場合可在任意角度位置安裝；
軟著陸：沖壓軟到位技術，使作動時噪音小及保護您的模具；
故障少：無油壓系統溫升之困擾；
空間?。号c普通氣缸及液壓站相比，占用空間面積可小于50%以上；
Product features:
fast speed: the speed is hydraulic drive fast, and more pressure stable transmission;
easy to use: cylinder device has the advantages of simple structure, easy adjustment for output, convenient use and maintenance;
output: in high output up to press the same way conditions, non pure pneumatic system can achieve;
low prices: equipment at a hydraulic system low;
easy maintenance: because of its simple structure, the hydraulic system maintenance is simple;
low energy consumption: continuous pressure or stop the action, not as pure as the motor to hydraulic system, continuous operation, so the energy can be saved, and the power source is easy to take, the actual energy consumption is equivalent to the hydraulic system of 10%-30%;
no leakage: energy conversion is convenient, can achieve zero leakage do not have to worry about environmental pollution;
loss model: in order to meet the process requirements, pressure and stroke work within the prescribed scope can achieve stepless adjustable;
easy installation: installation method, according to the different working conditions can be installed at any angle position;
soft landing: soft in place of stamping technique the die when moving, low noise and protect your;
less failure: no hydraulic system temperature rise of distress;
small space: compared with ordinary cylinder and the hydraulic station, the space occupation Area of less than 50%;

產品注意事項：
由于增壓缸經常處于高速運轉狀態，容易造成機器磨損，所以應按操作說明書來作業，增壓缸的工作溫度在-5℃~60℃左右，操作速度50~1000mm/s，為了保證增壓缸的正常工作，使用中應注意以下幾點：
1.保持清潔。
在將增壓缸接入氣路前，敬請先將管路及元件內的灰塵等雜物清除，以免降低增壓缸的使用壽命。
2.正常氣壓范圍內使用。
缸在正常使用時工作氣壓須要按照檢驗報告中規定的工作氣壓范圍內工作，不得超過規定的工作壓力.。
3.注意增壓缸的工作環境。
缸在設計時工作環境內的溫度已定，若因工作需要變換工作環境超過溫度需與增壓缸技術相關人員聯系處。由于缸中的部分元件為鐵質，所以請不要將其置于工況環境特為復雜的環境內使用(如有化學物質的接觸環境)，另請在缸前端加裝有效的空氣處理元件(三點組合)并接時加油潤滑及排水處理。
4.不可擅改加其它液壓油。
增壓缸在設計時所選用的液壓油價質為VG68#抗磨液壓油，不可撤擅自改用其它液體介質(如機油.水等)。
5.一定要按程序操作。
動作程序一定要按照氣路配裝圖的動作程序工作即預壓動作-增壓動作增壓釋壓-預壓復位。
6.注意保養，經常檢查增壓缸運轉。
為避免缸在增壓時動作的壓力過大破壞您的模具或工件，敬請在增壓段進入口處加裝一減壓閥,以便能有效保護您的產品。為確保增壓缸工作的穩定性，建議盡可能在三聯件與增壓缸之間并聯加裝一儲氣筒。
使用增壓缸500000次以上或半年以上時，建議將缸中的液壓油全部更換一次，以提高缸的使用壽命和工作年限。
Note:
because the pressurization cylinder often operates at high speed, easy to cause the machine wear, so should according to the operating instructions to operation, pressurized cylinder working temperature -5 ℃ ~60 ℃, the operation speed of 50~1000mm/s, in order to guarantee the normal work of the pressurizing cylinder, should pay attention to the following points:
1.the use of clean.
The pressure cylinder access gas path before, please first line and components of dust and other debris removal, so as not to reduce the service life of the pressurizing cylinder.
2.normal pressure range use.
Cylinder working in normal use pressure must work in accordance with the working pressure range specified in the test report, shall not exceed the prescribed work pressure.
3.note pressure cylinder working environment.
Cylinder in the design time environment within the temperature is fixed, if need because of the job transform working environment temperature and pressure cylinder over related technical personnel office. Because the component cylinder is iron, so please do not use it under the conditions for complex environment (such as exposure to environmental chemicals), please air handling units installed in front of effective cylinder (three points) and joint lubrication and drainage treatment.
4.can not be repeated and other hydraulic oil.
Hydraulic oil pressure cylinder in the design quality for the selected VG68# anti-wear hydraulic oil, can not be removed or switch to other liquid medium (such as oil. Water etc.).
5.we must operate according to the procedure.
Action program must be in accordance with the pneumatic loading diagram of the action program of work pressure action - pressurization action supercharging pressure release and pre press reset.
6.pay attention to maintenance, often check the pressure cylinder operation.
To avoid pressure cylinder in boosting the excessive damage your mold or workpiece, please in the booster section into the mouth is provided with a pressure relief valve, so that it can effectively protect your products. In order to ensure the stability of pressure cylinder work, suggestions as far as possible in the triplet and the pressurizing cylinder equipped with a parallel between the air storage reservoir.
The use of the pressurizing cylinder is more than 500000 times or more than half a year, suggested that hydraulic cylinder of all change, in order to improve the service life of the cylinder and working life.